The BelAire 318VL 7.5 HP combines a belt-driven two-stage cast-iron pump with an 80-gallon vertical receiver rated to 175 PSI, while using a footprint of approximately 39" × 24". The vertical design keeps valuable shop floor space available for vehicles, benches, and walkways, while the 208–230V single-phase motor makes this compressor suitable for facilities without three-phase service. A factory-installed magnetic starter provides motor overload protection. Note: published overall height figures differ between sources, so confirm the exact height and required ceiling clearance before ordering; the machine weighs approximately 479 lbs.
The two-stage pump uses solid cast iron construction and stainless steel valves for a serviceable design intended for regular shop use. Compressing air in two stages allows the pump to reach its 175 PSI maximum working pressure, while the belt drive separates the motor from the pump and provides a straightforward arrangement for maintenance. The vertical receiver also makes routine checks easier, with the oil sight glass and pressure controls positioned within practical reach. This model uses a manual tank drain, so condensate must be removed by the operator rather than automatically. Regular draining is important because moisture collects in the receiver during normal compression and can eventually reach downstream air lines and equipment.
This compressor is a good fit for small and mid-sized automotive shops, two-bay service facilities, home garages, and collector garages where floor space is limited and only single-phase power is available. Its compact base can fit against a wall or into a corner without consuming the long section of floor required by a horizontal receiver. Before installation, confirm that your electrical panel can support the recommended 60-amp circuit, have a qualified electrician verify the actual electrical requirements, and provide a flat, solid floor with enough clearance around the pump for service. With its tall vertical profile, adequate overhead space is just as important as the compact footprint.
Specifications
| Specification |
Value |
| Motor |
5 HP, 1-phase, 208-230V |
| Recommended breaker |
40 amp |
| Magnetic starter |
Not fitted |
| Pump |
Two-stage, belt drive, splash lubricated, solid cast iron cylinder |
| Rated delivery at 100 PSI |
18.5 cubic feet per minute |
| Delivery at 175 PSI |
16.6 CFM |
| Maximum pressure |
175 PSI |
| Aftercooler |
None |
| Tank |
80 gallon, manual drain |
| Tank orientation |
Published inconsistently — see below |
| Dimensions |
39" × 24" × 77" |
| Weight |
428 lbs |
Confirm the Tank Orientation Before You Plan the Bay
Published records conflict on tank orientation: the product copy and one specification field say vertical, while the specification table says horizontal.
The listed dimensions — 77" tall on a 39" × 24" footprint — support the vertical interpretation, but that is an inference, not confirmation. If orientation affects your installation, confirm it with us in writing before ordering and we will verify it against the factory documentation.
Certification, Stated Plainly
The tank is built to the American pressure-vessel code and the current product copy also states Canadian pressure-vessel registration. These certifications apply to the tank, including its design, welding, inspection and safety valve.
They do not constitute a third-party safety listing for the complete electrical machine. If your insurer, plant safety policy or local authority requires that type of listing, ask us before ordering and we will confirm the available documentation in writing.
Shipping & Delivery
Ships by freight to the lower 48 states, not by parcel carrier. The machine weighs 428 lbs and stands 77" tall. Freight is quoted live at checkout for your delivery address. Residential delivery carries an additional fee; terminal pickup is an alternative.
Plan unloading before delivery. Arrange a forklift, loading dock or other suitable equipment. Inspect the crate with the driver present, checking the shroud, belt guard, gauges and tank for damage. Record any issues on the delivery paperwork and photograph the shipment before accepting it.
Warranty
The listing states a 2-Year factory warranty for consumer and commercial use, with the full warranty document available on this page.
If a component fails, contact us before disassembly. The manufacturer may need to inspect the affected part in its failed condition. Stop using the machine, photograph the issue, and keep the pump or pressure switch intact until the claim process provides further instructions.
